TPO Molded Sealant Pockets for Pourable Sealer
TPO Molded Sealant Pocket 6" to 11-1/2" Combinations
Interlocking, two-piece, injection-molded, weldable pockets used to waterproof pipe clusters or other oddly shaped roof penetrations. TPO Molded Sealant Pockets for pourable one-part sealer roof penetrations and conduit bundles. The 2” vertical wall creates a perimeter around the penetration while the reinforced TPO flange ties into the existing eld membrane. Injection molded with cutting guides at 6 different points allow these flashing pockets to easily be cut to size, and provide sizing flexibility while on the job. The two-piece design allows for fast, easy installation by removing the need to disconnect conduits or lines.
- Material: TPO
- Size: 6" x 7.5" to 11.5" Multiple Combinations (Cut to Size)
- Application: The two-piece design allows for fast, easy installation by removing the need to disconnect conduits or lines.
- Color: White
TPO Molded Sealant Pockets for sealing single-ply roofing penetrations with interlocking, two-piece prefabricated pockets of non-reinforced TPO material used to seal pipe clusters or other irregular shaped penetrations. Pockets length can be adjusted from 7-1/2" to 11-1/2" by following the pre-molded cutting lines. Used with pourable sealant and primer, this product effectively waterproofs pipe clusters or other odd shaped penetrations on WeatherBond Pro roofing systems.
- 7 Possible Size Combination Options: Fits multiple size penetrations
- Reduce Install Costs and get off the roof faster
- Save up to 60% of labor
- Waterproof difficult penetrations
- No disconnecting conduits or lines
- Material: TPO
- Size: 6" - 11.5" Multiple Combinations (Cut to Size)
- Application: The two-piece design allows for fast, easy installation by removing the need to disconnect conduits or lines.
- Color: White
INSTALLATION:
Sealant Pockets shall be installed in accordance with the recommendations and specifications of the roofing material manufacturer.
1. Prepare all welding surfaces by cleaning with TPO membrane cleaner.
2. Fit both pieces of sealant pocket together around the penetration.
3. If smaller size is required, remove excess material by cutting along vertical guidelines.
4. Heat weld the vertical and horizontal overlaps completely.
5. Heat weld flange to eld membrane.
6. Fill sealant with specified sealant (sold separately).
SIZE COMBINATIONS |
|
|
Opening |
Depth |
Flange |
| 6" x 6" | 2" | 10" x 10" |
| 6" x 7" | 2" | 10" x 11" |
| 6" x 8" | 2" | 10" x 12" |
| 6" x 9" | 2" | 10" x 13" |
| 6" x 10" | 2" | 10" x 14" |
| 6" x 11" | 2" | 10" x 15" |
| 6" x 12" | 2" | 10" x 16" |
MATERIAL PROPERTIES & CHARACTERISTICS |
||
|
Material |
Thickness |
Color |
|
TPO |
.060” (60 mil) |
White |
| SKU | FLA-STSPI |
|---|---|
| Manufacturer Part Number | STSPI |
| Manufacturer | FlashCo. |
| Weight | 5lb |
| Country of Manufacture | United States |
| Length | 12in |
| Width | 12in |
| Height | 12in |
Interlocking, two-piece prefabricated pockets of non-reinforced TPO material used to seal pipe clusters or other irregular shaped penetrations. Pockets length can be adjusted from 7-1/2" to 11-1/2" by following the pre-molded cutting lines. Used with pourable sealant and primer, this product effectively waterproofs pipe clusters or other odd shaped penetrations on WeatherBond Pro roofing systems.
-
6 size options to fit multiple size penetrations
-
Get off the roof sooner
-
Reduce installed costs
-
Save up to 60% of labor
-
Waterproof difficult penetrations
-
No disconnecting conduits or lines
SIZE COMBINATIONS |
|
|
|
Opening |
Depth |
Flange |
|
| 6" x 6" | 2" | 10" x 10" | 6-Pack / Box |
| 6" x 7" | 2" | 10" x 11" | 6-Pack / Box |
| 6" x 8" | 2" | 10" x 12" | 6-Pack / Box |
| 6" x 9" | 2" | 10" x 13" | 6-Pack / Box |
| 6" x 10" | 2" | 10" x 14" | 6-Pack / Box |
| 6" x 11" | 2" | 10" x 15" | 6-Pack / Box |
| 6" x 12" | 2" | 10" x 16" | 6-Pack / Box |
MATERIAL PROPERTIES & CHARACTERISTICS |
||
|
Material |
Thickness |
Color |
|
TPO |
.060” (60 mil) |
White |
INSTALLATION:
Sealant Pockets shall be installed in accordance with the recommendations and specifications of the roofing material manufacturer.
1. Prepare all welding surfaces by cleaning with TPO membrane cleaner.
2. Fit both pieces of sealant pocket together around the penetration.
3. If smaller size is required, remove excess material by cutting along vertical guidelines.
4. Heat weld the vertical and horizontal overlaps completely.
5. Heat weld flange to eld membrane.
6. Fill sealant with specified sealant (sold separately).
