CHEM LINK

NovaLink FP • Flash & Patch Liquid Rubber

In stock
As low as $5.95

NovaLink™ FP is a non-toxic, moisture cured, liquid rubber caulk & sealant designed to fill, seal & level grout lines, fill voids, fill seams & repair surface damage on any residential or commercial roof, or to waterproof other construction materials. NovaLink FP is compatible with a wide range of substrates & is a Low-VOC Green product and is elastomeric which means it will stretch & shrink properly with the hot & cold  temperature changes of seasons.

NovaLink Flash & Patch is perfect for sealing & waterproofing around chimneys, asphalt roof shingles, roof seams, flashing, parapets and other areas. NovaLink FP can be applied in cold weather at temperatures as low as 35°F, in wet or dry conditions, and will not degrade from direct exposure to sunlight. 

  • SOLVENT FREE: 100% solids, will not shrink
  • ADHERES: bonds to damp concrete
  • TACK FREE: 60 minute skin over
  • NO OUTGASSING: no outgassing on damp surfaces

NovaLink FP formerly called BARR Flash & Patch from ChemLink.

Financing Available for orders over $1,000

NovaLink™ FP is a moisture curing elastomeric waterproofing & sealant designed to fill, seal & level grout lines, voids, seams & surface damage on construction materials before the application of liquid waterproofing.

NovaLink FP may be used to repair and level surface defects, grout lines, joints and penetrations in waterproofing applications. In transition joints, or where damage is excessive, reinforce with Tietex T-326 fabric. In right angle joints use NovaLink FP to form a one inch cant. NovaLink FP may also be used for repairing roof leaks, asphalt shingles, roof valleys and seams, chimney flashings, and emergency roof repairs.

Basic Uses:

  • Above grade waterproofing
  • Below grade waterproofing
  • Roof Repairs
  • Sealing parapets
  • Lining gutters and valleys
  • Planter boxes
  • Lining HVAC condensation pans

Compatible Substrates:

  • Concrete
  • Steel
  • Block and Brick
  • Aluminum Stone
  • Galvanized Metal
  • Masonry
  • Isoboard
  • Plywood and OSB
  • Untreated Wood
  • EPS (Expanded Polystyrene)
  • FRP (Fiber Reinforced Plastic)

NovaLink FP is a non-toxic, black, liquid rubber Low-VOC caulk/sealant/waterproofing material that dries to a black gloss.

*NovaLinkâ„¢ FP Gun Grade Flash & Patch is a moisture curing, elastomeric waterproofing material for use in repairing roof leaks, shingles, roof valleys, seams, chimneys and flashings

More Information
SKU CHE-F1110-BL
Manufacturer CHEM LINK
Weight 1lb
Country of Manufacture United States
Product Sheet (658.65 kB)

INSTALLATION:

  • Do not use at temperatures below 35 degrees F (2 degrees C.)

  • Maintain NovaLink FP materials above room temperature before applying.

  • Remove all dirt, oil, loose paint, water, frost and other contamination that can interfere with bonding.

  • Form release residue and lime should be power washed and allowed to dry.

  • NovaLink FP may be applied to green concrete without out-gassing.

  • Although concrete cure times may vary with temperature, for optimum bonding, concrete cure time should be three to seven days.

  • Application surfaces must be dry the touch and free of obvious moisture.

  • NovaLink FP may be used to repair and level surface defects, grout lines, joints and penetrations in waterproofing applications.

  • In transition joints, or where damage is excessive, reinforce with Tietex T-326 fabric. In right angle joints use NovaLink FP to form a one inch cant.

Tack Free Time: 60 min +/- 15

Shrinkage: No visible shrinkage after 14 days

Service Temperature: -40°F to 200°F (-40°C to 93°C)

NovaLinkâ„¢ FP Gun Grade Flash & Patch is a moisture curing, elastomeric waterproofing material for use in repairing roof leaks, shingles, roof valleys, seams, chimneys and flashings